User manual and frequently asked questions X-Clean 10, Wet Dry Cordless Vacuum Cleaner, Long Run Time, Self Cleaning and Drying
The best of cleaning at a glance
Référence : GZ7035WO
Voir les documents liés
Voir les questions les plus fréquentes
FAQ
After one pass, it takes about 3 minutes to dry.
There is no need to vacuum, the X-Clean can vacuum and wash solid and liquid waste.
If there is a large amount of dry debris on the floor, you can vacuum first to avoid filling the tank of the X-Clean too quickly.
If there is a large amount of dry debris on the floor, you can vacuum first to avoid filling the tank of the X-Clean too quickly.
Yes, you can use water up to a maximum of 50°C. Beyond that, the heat can damage the washer’s seals and reduce its durability.
The X-Clean washer can be used on all types of smooth floors: waxed concrete, tiles, terracotta, PVC, linoleum, parquet.
For parquet or more delicate floors, don't hesitate to use modes with a low water flow to avoid soaking them.
We recommend testing the appliance on a small area for delicate floors when using it for the first time.
Refer to product safety and use instructions.
Do not use on carpets, walls, windows or floors sensitive to water.
Product is not designed for outdoor use.
For parquet or more delicate floors, don't hesitate to use modes with a low water flow to avoid soaking them.
We recommend testing the appliance on a small area for delicate floors when using it for the first time.
Refer to product safety and use instructions.
Do not use on carpets, walls, windows or floors sensitive to water.
Product is not designed for outdoor use.
No, it doesn’t : it is specially designed to clean your hard floors without causing any damage.
However, we recommend testing the device on a delicate area during the first use.
Refer to product safety and use instructions.
However, we recommend testing the device on a delicate area during the first use.
Refer to product safety and use instructions.
We do not recommend using the X-Clean washer on carpets.
Even though they can pick up dirt, washers wet fabrics, which can leave marks or promote bacterial growth.
The recommended use for our washer remains hard floors.
Even though they can pick up dirt, washers wet fabrics, which can leave marks or promote bacterial growth.
The recommended use for our washer remains hard floors.
Our X-Clean ranges cannot be used without water and with dry vacuuming.
To use the X-Clean washing vacuum cleaner, the clean water tank must be filled.
On the X-Clean 10 model, you can still use the "Suction" mode, which reduces the water flow to the minimum for minimal moistening of the floor.
To use the X-Clean washing vacuum cleaner, the clean water tank must be filled.
On the X-Clean 10 model, you can still use the "Suction" mode, which reduces the water flow to the minimum for minimal moistening of the floor.
Even if the washer is compatible with most household cleaners on the market, this remain optionnal.
You are responsible for this; please follow these instructions:
Prefer multi-surface detergents suitable for various types of floors. Use solutions with mild surfactants. Do not use products containing bleach, pure bleach, or corrosive agents. Do not use foaming cleaning products (carpet shampoo, black soap, dishwashing liquid). Do not use acid-based cleaners, such as certain bathroom products. These are too harsh and may corrode the vacuum mop’s metal components. Do not use greasy (e.g., black soap), toxic, flammable, aggressive, or particle-containing products. Adding household detergents to the water tank is done at your own risk. Using incompatible detergents may damage and cause your device to malfunction. This could cause a product dysfunction.
You are responsible for this; please follow these instructions:
When using detergents, always follow the dosage recommended by the manufacturer to avoid residue on the floor and to ensure quick drying.
Overdosing the detergent may damage your device and cause it to malfunction.
Overdosing the detergent may damage your device and cause it to malfunction.
The X-Clean 10 washing vacuum cleaner is equipped with anti-winding technology that effectively cleans hair and fur, which will go directly into the dirty water tank.
The X-Clean washing vacuum cleaner automatically recharges when you put it back on its base, which must be plugged in.
Once fully charged, the appliance will turn off automatically, there is no need to unplug your base.
Once fully charged, the appliance will turn off automatically, there is no need to unplug your base.
To adjust or turn off voice assistance, your device must be placed on its base, and :
• For language switching: press the MODE + Self-Cleaning buttons briefly & simultaneously, repeat until the correct language is found
• For volume modification: keep pressing the MODE button for 2 seconds
Detail in the image below :
• For language switching: press the MODE + Self-Cleaning buttons briefly & simultaneously, repeat until the correct language is found
• For volume modification: keep pressing the MODE button for 2 seconds
Detail in the image below :
Your appliance only switches on and starts by pressing ON in the working position, not in parking mode.
To adjust the voice assistance, your device must be on its base, and:
• To change the language: briefly press the MODE + Self-cleaning buttons simultaneously. Repeat the operation until you find the right language.
• To change the volume: press and hold the MODE button for 2 seconds.
• To change the language: briefly press the MODE + Self-cleaning buttons simultaneously. Repeat the operation until you find the right language.
• To change the volume: press and hold the MODE button for 2 seconds.
It's important to do this immediately after using your appliance.
It's very simple and only takes a few seconds. It cleans the brush by removing accumulated dirt and wringing it out.
After this self-cleaning, we recommend that you place the brush to be dried on the drying rack provided.
It's very simple and only takes a few seconds. It cleans the brush by removing accumulated dirt and wringing it out.
After this self-cleaning, we recommend that you place the brush to be dried on the drying rack provided.
After each self-cleaning cycle, it is important to empty both of your appliance's tanks.
However, it is not necessary to wash the roller and the rest of the appliance.
For this step, we recommend (depending on your frequency of use and type of dirt vacuumed) that you wash your roller once a week.
However, it is not necessary to wash the roller and the rest of the appliance.
For this step, we recommend (depending on your frequency of use and type of dirt vacuumed) that you wash your roller once a week.
Brush wear depends mainly on the surface of the floor. If your home is covered only with tiles, the brushes will last longer than those used on rougher surfaces such as terracotta or concrete.
In all cases, you'll notice with the naked eye when the bristles on your brush start to get damaged.
The average recommendation is to change your roller every 6 months.
In all cases, you'll notice with the naked eye when the bristles on your brush start to get damaged.
The average recommendation is to change your roller every 6 months.
No, the roller is not compatible with the washing machine, which could damage it and then damage your appliance.
If your roller is dirty, and you want to wash it more thoroughly, we recommend that you wash it under the tap with washing-up liquid, and then rinse it thoroughly to remove any residue.
If your roller is dirty, and you want to wash it more thoroughly, we recommend that you wash it under the tap with washing-up liquid, and then rinse it thoroughly to remove any residue.
Always use the device with the roller in place and the clean water tank full.
If a foreign object is stuck in the cleaning head, clean it.
Check that the washing head is not damaged.
If a foreign object is stuck in the cleaning head, clean it.
Check that the washing head is not damaged.
An object or fibres may be blocking the roller.
If so, dismantle your roller and remove any items that are preventing it from rotating. Also check between the roller and the side brush if there is one.
If so, dismantle your roller and remove any items that are preventing it from rotating. Also check between the roller and the side brush if there is one.
The roller may be dirty. If this is the case, run a self-cleaning cycle and then clean the roller by hand.
If the problem persists, the appliance may not be set to the correct cleaning mode.
Adjust the operating mode according to the level of dirt on your floor. A stubborn stain will take longer to clean than a superficial stain.
We therefore recommend using the ‘MAX’ mode on the vacuum cleaner and letting the roller run over the stain for a few moments to moisten it thoroughly, then going over it several times to remove the stain.
If the problem persists, the appliance may not be set to the correct cleaning mode.
Adjust the operating mode according to the level of dirt on your floor. A stubborn stain will take longer to clean than a superficial stain.
We therefore recommend using the ‘MAX’ mode on the vacuum cleaner and letting the roller run over the stain for a few moments to moisten it thoroughly, then going over it several times to remove the stain.
If the water flow is too high or the roller is soaked, set the appliance to minimum water flow.
If there is a water leak from the vacuum cleaner, contact an authorised repairer, who will be able to help you resolve the issue.
If there is a water leak from the vacuum cleaner, contact an authorised repairer, who will be able to help you resolve the issue.
The presence of foam in the dirty water tank can cause incorrect detection and make the system think the tank is full.
Rinse and clean the dirty water tank, without using foaming detergent. Do not forget to fill the clean water tank.
Rinse and clean the dirty water tank, without using foaming detergent. Do not forget to fill the clean water tank.
To start, your device must be in the running position: tilt the vacuum cleaner and press the ON/OFF button.
Parking mode will stop the device and you will not be able to restart it in this position.
If the vacuum cleaner is broken, please contact our authorised repairers who will be able to help you.
Parking mode will stop the device and you will not be able to restart it in this position.
If the vacuum cleaner is broken, please contact our authorised repairers who will be able to help you.
The brush cover or roller may not be fitted correctly. Please remove them and refit them, or replace them.
The charging base may not be plugged in, or the charger may be incorrectly connected to the base.
If the clean water tank is empty, fill it up.
The water distribution system may be clogged. In that case, clean the nozzles with the cleaning brush provided and/or a damp cloth.
If this is not enough, fill your water tank with cold white vinegar and run a Self-Clean cycle.
When the water flow is too low, make sure you are using INTELLIGENT mode or TURBO mode to optimise cleaning.
The water distribution system may be clogged. In that case, clean the nozzles with the cleaning brush provided and/or a damp cloth.
If this is not enough, fill your water tank with cold white vinegar and run a Self-Clean cycle.
When the water flow is too low, make sure you are using INTELLIGENT mode or TURBO mode to optimise cleaning.
Take your device to a recycling center or waste disposal facility.
If you believe a part is missing, please contact our customer service center and we will help you find an appropriate solution.
Please go to the “Accessories” section of the website to easily find whatever you need for your product.
Find more detailed information in the Guarantee section of this website.
We do not currently offer a rental service for this device. You can buy it directly from us or from our partners.
